Antique cast iron architectural hardware is beautiful, but what's the best way to protect it from rusting? Would you believe it may be as simple as giving it a bath?

I picked up this method of treating cast iron many years ago while working in a window restoration shop. It's a tried and true method for protecting cast iron from rust, but there isn't a whole lot of information about it on the Internet. So it's our hope this will go a long way to helping others looking to restore their windows or other cast iron hardware in a classic and lasting manner.

We're very fortunate to have several of our original windows almost completely intact. This means that our original cast iron sash pulleys are also in place and fully functional. However, they were all creatively disguised by many layers of paint, hiding their utilitarian beauty.

As beautiful as these original architectural details may be once stripped, they're also made of cast iron and are prone to rust. A few years ago we stripped and reinstalled several of our pulleys without protecting them from the elements. Even though they aren't directly exposed to water, the humidity in the air and blowing rain or snow is enough to leave surface rust on exposed portions of the iron. The end result after a few years in the window frame is a fine coating of the orange-brown patina we'd like to avoid, especially since it begins to stain the sash ropes.

In the past we've coated some of our cast iron hardware, like rim locks and hinges, or other ferrous metal that may get wet (like outdoor chairs), with low luster poly or Penetrol, but neither of those are very good options for these sash pulleys. The fact that the pulleys have moving parts and the sash ropes cause friction through use means that coating this hardware with something that can fracture and flake off isn't a great solution.

Last week we touted the rejuvenating characteristics of boiled linseed oil and turpentine (or Blopentine) for breathing life into our old window sash, but what can linseed oil do for ferrous metal? Turns out, it can be a great option for keeping cast iron from rusting.

If you've ever tried seasoning cast iron (like what you might do to cast iron cookware) you might be familiar with using oil to keep it from rusting. The idea in what we're doing is very similar. Heating the pan and allowing the oil (often flaxseed oil for cast iron pots) to coat and protect the cast iron helps prevent the cast iron from rusting by keeping water away from direct contact with the metal. It essentially forms a thin protective film over the iron's pitted and porous surface.

In our case we're using some Linseed Oil Soap from Allback, and we're giving our sash pulleys a linseed oil bath. The linseed oil soap is a mixture of organic linseed oil (not boiled linseed oil) and water, and can be diluted by adding it to the water in our "bath."

For us the first step is to clean the sash pulleys of their rush with a little steel wool. We previously used a wire wheel to completely clean the paint, but this thin layer of rust was no match for a #1 and #00 steel wool pad.

Once clean we moved onto the bath. We're using the vintage Crock-Pot I scored for free, coincidentally on the day after it was revealed on This Is Us (*SPOILER ALERT*) that Jack was killed by a vintage slow cooker, some crazy irony there, right? 

I added enough water to fully cover the sash pulleys and then put in a few squirts of the linseed oil soap.

The soap is slightly clouding the water to start...

...but mixes easily with the water to fully disperse. 

I went ahead and put the Crock-Pot on high to warm the soapy water up, and dropped the pulleys into the cloud.

Allowing them to soak in the hot mixture for several hours gives the linseed oil a chance to heat and fully coat and protect the cast iron. Also, this gives the mixture a chance to smell a little bit like hot gross fish. If you're into hot gross smelling fish, you'll really love this whole process!

While they cooked the water started to turn a bit brown. I periodically spun the pulleys around to make sure there was no trapped air or areas not fully exposed to the bath. As you can see from the photos, the case iron did slightly darken from the water and oil, but that's expected.

After three hours or so I checked on the progress. Removing the pulleys from the hot oil bath revealed a great looking piece of hardware that's ready for another 100 years of service.

The pulleys are slightly tacky right after they've been removed from the bath, but allowing them to dry overnight yielded a smooth and fully dried end result. The final finish is very matte and there is not a plastic film look to it at all, as you'd expect from a traditional poly.

Our sash pulleys, with patent date of Feb 1879, are once again ready for reinstall. These one screw Norris style pulleys (based on their shape and the specialized mortise necessary for the window frame) should no longer be prone to rust if they encounter a little bit of moisture. After the linseed oil bath they now have that classic cast iron dark grey patina. There is no film left following the bath and the coating is more or less baked in over the entire pulley.

This linseed oil bath is a great option for hardware with movable parts that may be exposed to moisture. At the same time, it's even a great option if you want that raw cast iron look without the need for maintenance or a glossy coating of poly. We'll probably be using this method for future restoration of our rim locks after we're done cleaning off all of the rust.

Have you ever heard of using a linseed oil bath on cast iron hardware? Or maybe you're a fan of linseed oil soap as an organic and environmentally friendly method to cleanse difficult to clean surfaces? Would love to know if you found this tip useful and if you think you'll try it out some day.

Comments 6

Comments

Tee
3/9/2018 at 6:56 PM

This is good information. I'm going to pass this along to my husband for future projects.

Peggy Gustafson (Margaret)
8/2/2018 at 10:34 AM

Have enjoyed reading your informative articles in the Old House
Journal that I have subscribed to for decades.

In the Oct. 2017 edition your "Know-How" article addresses how transom windows work. Was wondering how your information could be made available to the folks in Gettysburg who are new to "old house" ownership repairs and/or to folks who have finally decided to make their old transoms useful in circulating out the hot humid air of their old and loved home.

I am a long time member of Gettysburg's Historic Architectural
Review Board and try to make useful information available to owners of old buildings. Information may be presented to:
local newspaper, at meetings, on line or in print at the Borough Office or the Gettysburg ( Pennsylvania ) Library.

Your name and the copy would be presented as found in the original format when possible.

Would you be in favor of this usage and how could this become
a reality for those who have yet subscribe to Old House JOurnal.

I thank you for your consideration of the request and for the
help you have provided to me in the past and hopefully future.

Peggy

Kurt Christensen
1/24/2019 at 8:48 PM

Your window restoration series is great!! I'm going through the same process on a 1926 house in St Paul, MN. I only wish I'd seen your blog posts 6 months ago - would definitely have saved me some trial and error!

One alternative I'll suggest to your linseed oil bath is to do the old blacksmithing technique of heating up the pulleys (I used a plumbing torch) and then brushing boiled linseed oil on them with a rag. The downside is that it's a finicky process to get the finish just right (and you have to wear a real mask - the fumes are not good!), but the plus side is that I can get a deep, almost black finish, to better match the oil-rubbed bronze window hardware we selected.

Your pulleys look gorgeous, though - just depends what kind of finish you want. Looking forward to more blog posts!

David G
2/2/2020 at 3:14 PM

Good stuff!

Few questions:

  1. Is the first photo the “after” of this process? It does not look as dark as the photos further down in the post where it appears the process is complete. Or perhaps you buffed them a bit?

  2. We have window hardware with both iron and brass. Does this process work for brass hardware as well, or will it discoloring be too prominent?

DG

Bennett
4/24/2020 at 3:40 PM

Can this method be employed with 100% pure tung oil (or diluted) instead of linseed oil? Is there a specific reason to use the linseed soap?

I’m restoring the windows in my 1900 Queen Anne and am very interested in your process here.

Thanks!

Bennett

Since you've not signed in yet, you will need to fill in your name and email below. If you have a Facebook account, save yourself a step and use Connect to login.

Denotes a required field.

Please enter full URL, including http://

You can use Markdown syntax in your comment. And you can also use lots of Emoji!
  • Search

  • Login
  • Follow
  • Advertising

If you're looking for information on advertising and sponsorships, head on over to our sponsorships page. You can purchase site sponsorships in a few easy clicks. 

Toolbox Tuesday
Open Housing
  • We're Featured!

Old Town Home has been featured in the following places and publications:

The Washington Post
 
Washingtonian Magazine
 
Domino
 
Old House Journal
 
 
Apartment Therapy House Tour
 
Washington Post Express Feature
 
Home & Garden Blogs
 
© 2024 OldTownHome.com. - Privacy Policy
Login Below
or
Sign in with Facebook
Connect

Unexpected Error

Your submission caused an unexpected error. You can try your request again, but if you continue to experience problems, please contact the administrator.

Working...

Working...